Technical Data

Home  /  Technical Data

Technical Data

Grades, Coatings, Tolerances And Curves

Everything an engineer needs to specify a magnet: which grade holds its flux at your temperature, which coating survives your environment, and what tolerance we can hold on your dimensions.

NdFeB

N35–N56 · M / H / SH / UH / EH / TH · 80–230 °C · Br up to 1.50 T

SmCo

SmCo5 XG18–XG24 · Sm2Co17 XGS26–XGS33H · up to 350 °C

Ferrite

Y10T–Y35 including Y26H–Y33H high-coercivity grades · 200 °C

Grade Selection

Pick The Grade By Temperature, Not By Habit

The same geometry can behave very differently at temperature. Choosing a grade with enough intrinsic coercivity for your worst-case temperature is the single most important specification decision.

NdFeB grade and temperature chart
Coatings

Surface Treatment Options

Typical coating performance for sintered NdFeB. Salt-spray (NSS), humid-heat, PCT/HAST and maximum service temperature are listed for each system.

CoatingThickness (μm)Neutral Salt Spray (h) Humid Heat (h)PCT / HAST (h)Max Use Temp (°C)
Zinc (Zn)5–15≥48——≤160
Nickel (Ni)10–30≥96≥50096≤200
Ni + Sn10–30≥9650096≤200
Ni + Au10–30≥9650096≤200
Ni + Ag10–30≥967248≤160
Epoxy10–30≥727248≤160
NiCu + Epoxy20–40≥500500200≤160
Ni + Epoxy20–40≥500500200≤160
Vacuum-plated Al5–30≥100500200≤400
Al + Epoxy15–30≥200500200≤160

Corrosion resistance also depends on part geometry — edges and sharp corners corrode first. Share your drawing and we will recommend a coating system.

Magnetization

Magnetization Directions

Direction determines how the flux leaves the part — and it must be fixed before tooling. We magnetize square blocks along length, width or thickness; rings axially or radially; and tiles radially, through width or through thickness.

Magnetization direction options
▭

Square & Block

Along length, width or thickness.

◯

Ring & Cylinder

Axial, radial or multi-pole.

◗

Tile & Arc

Radial, width or thickness.

Tolerances

Machining Tolerances (mm)

Standard achievable tolerances for blocks, discs, rings and arcs. Tighter values are possible on request, depending on size and coating.

Size rangeDimensionsGeometry
Outer ØInner ØLength LWidth WThickness T FlatnessParallelismPerpendicularityRoundnessConcentricity
≤ 5 mm0.030.050.040.040.040.020.030.030.020.04
5 < L ≤ 30 mm0.050.060.060.060.060.020.040.050.020.05
30 < L ≤ 70 mm0.080.10.080.080.080.040.060.10.030.1
70 < L ≤ 120 mm0.080.150.10.10.10.040.080.150.050.15
120–200 mm0.150.180.150.150.150.060.120.30.060.3

Values are typical production tolerances in millimetres for uncoated parts; plating adds 10–30 μm per surface depending on the system.

Achievable machining tolerance chart
Curves

Demagnetization Curves

B-H and J-H curves measured at elevated temperature — use them to check your working point and load line.

Grade 42EH

Grade 42EH
20–200 °C

Grade 35AH

Grade 35AH
20–200 °C

Grade 45UH

Grade 45UH
20–180 °C

Grade N50H

Grade N50H
20–120 °C

Grade N50M

Grade N50M
20–100 °C

Need A Data Sheet?

Tell us the grade and geometry you are considering and we will send the matching curve, tolerance and coating data.

Menu

Get a Quick Quote

You can get a price or send us any questions to get any information you would like to know, and we will reply to you as soon as possible.

Update cookies preferences